Skip to main content


Open Main MenuClose Main Menu

Round Bale Hay Storage

Large round bales were introduced in Oklahoma in the early 1970s. One of the reasons for the popularity of this hay package was its low-labor demand. Harvesting and storing round bales only requires one to two people; whereas, two to four people are often needed to harvest and store small square bales. Also, large round bales have fewer storage requirements. In most cases, square bales must be stored under cover and in an enclosed barn. Round bales, however, are often stored outside and unprotected because their shape enables them to shed precipitation. Still, there are many uncertainties about projected storage losses in exposed large round bales and the economic benefits of providing some type of protection.


Generally, the value of a storage system depends on the projected hay loss while in storage and the price of hay when sold or used. Table 1 shows the dollar value loss of hay based on a percentage of storage loss over a range of hay prices. For example, if hay with a market price of $80 per ton has a 20 percent loss during storage, the value of the hay lost would be $16 per ton. This cost of hay value lost added to the cost of the storage system, such as an enclosed barn, gives the total storage cost, which can be used to compare various types of storages. One of the biggest problems in determining the total storage cost of a system is estimating the loss of hay value during storage.


Table 1. Value of hay lost in storage.

    Hay price (per ton)      
Storage loss (%) $40 $60 $80 $100 $120
5 2 3 4 5 6
10 4 6 8 10 12
15 6 9 12 15 18
20 8 12 16 20 24
25 10 15 20 25 30
30 12 18 24 30 36
35 14 21 28 35 42
40 16 24 32 40 48

Note: Does not include losses associated with shrinkage or reduced quality.


Bales Stored Outside and Unprotected

Research has shown that storage losses in large round bales stored outside and unprotected can be far greater than hay producers realize. Quality indicators such as acid detergent fiber and dry matter disappearance can be adversely affected over 10 percent. Dry matter losses can reach 50 percent depending on bale quality, storage conditions and length in storage (Table 2). The lower value of each range represents well-formed bales located in areas such as northwestern Oklahoma with low rainfall (less than 25 inches annually) and low relative humidity. The higher values are for areas such as southeastern Oklahoma with high rainfall (greater than 40 inches annually) and high relative humidity.


Severe deterioration is usually confined to the outside two to eight inches of the bale. Depending on the bale’s diameter, just two inches can represent over 10 percent of the bale’s dry matter (Table 3). An eight-inch weathered layer represents a significant volume even in the largest round bale packages. The depth or thickness of weathering depends on many factors, including amount of rainfall and environmental conditions (temperature and humidity) during the storage period, the hay type and condition when baled, and bale shape and density.


Table 2. Percent dry matter loss of round hay bales.

   Storage Period  
Storage Method Up to 9 months* 12-18 months
Ground 5-20 15-50
Elevated 3-15 12-35
Ground 5-10 10-15
Elevated 2-4 5-10
Under roof 2-5 3-10
Enclosed barn less than 2 2-5

* If used before spring warn-up.


Table 3. Amount of dry matter in outer layers of large round bales.

   Outer Layer Depth ---------% dry matter loss      
Bale Dia., ft. 2" 4" 6" 8"
4 16 31 44 56
5 13 25 36 46
6 11 21 31 40
7 9 18 27 34
8 8 16 23 31


Bale Density

Bales should be well-shaped and as dense as possible. Limited research indicates storage losses for variable-chamber bales may be slightly less than fixed-chamber bales. One of the important keys to reducing weathering is the tightness of the outer layer of the bale. Moisture penetration and bale deterioration are inversely proportional to the tightness of the outer two to six inches. The tighter the outer layer, the lower the losses regardless of whether the bale was formed using a variable or fixed-chamber baler. Outer layer “tightness,” or density, is not easy to measure. One rule of thumb is to push on the outer surface of a newly-formed bale with the palm of your hand. If you can depress the surface more than about a half-inch, the bale could undergo significant storage losses when placed outside and unprotected. If using sisal or plastic twine, wraps should be no greater than eight inches (preferably six inches) apart on the bale. This does, however, require additional time and expense during baling. If bales are stored outside, the added time and expense are easily justified. Research shows net-wrapped bales have storage losses similar to the standard plastic or twine wrap when the outer layers are the same density.


Environmental Conditions

The amount of precipitation that falls on unprotected bales can affect storage losses. However, precipitation alone is not a good indicator of projected losses. In recent studies by Oklahoma State University researchers, storage losses were found to be related to precipitation combined with air temperature and humidity. Much of the dry matter loss associated with outside storage is the result of microbial respiration, where carbohydrates in the plant tissue plus oxygen are converted to carbon dioxide, water, and heat. Extended periods of warm, humid, and cloudy conditions with abundant rainfall are favorable for microbial activity, resulting in greater losses of forage dry matter and quality than in periods of cool, dry, and sunny conditions. To minimize storage losses, bales stored outside and unprotected should be used by early spring, before the air temperature, humidity, and precipitation significantly increase. In Oklahoma, bales should generally be used before March 1.


Storage site

The storage site is another important consideration in reducing bale losses. Select a site that is not shaded and is open to breezes to enhance drying conditions. The site should also be well-drained to minimize moisture absorption into the underside of the bales. As much as 12 inches of the bottom of a bale can be lost through moisture absorption resulting from the wicking action. Compare estimated losses for ground versus elevated storage provided in Table 2. Ground contact can account for over half of the total dry matter losses. Where practical, keep bales off the ground using low cost, surplus materials such as discarded pallets, racks, fence posts, railroad ties, and used tires. Another alternative is to use a layer of crushed rock about six inches deep to ensure good drainage within and around the storage site.



Bales should be stored in rows, buffed end-to-end, and oriented in a north/south direction. The combination of the north/south orientation and at least three feet between rows will provide for good sunlight penetration and air flow, which will allow the area to dry faster after a rain. Vegetation between rows should be mowed. Research has shown that orientation is a minor consideration if the bales are used before early spring because the losses are relatively small until that time. If stored into the summer, bales oriented in an east-west direction can experience severe deterioration on the north-facing surface.



Large, round bales stored outside and covered with plastic or canvas usually sustain much less deterioration compared to unprotected bales (Table 2). As shown in Table 4, the amount of covering per bale varies depending on the storage configuration. A single bale can require as much as 63 square feet to cover its top. If bales 5-feet diameter by 5-feet long are stacked three high, the size of the covering can be as low as 13 square-feet per bale.


Covering materials range in price from $0.06 per square foot for a 6-mil black polyethylene or plastic to over $0.75 per square foot for a tarp. To determine the cost of covering round bales, multiply the area of coverage (from Table 4) by the cost of the covering. Assuming a 6-mil black plastic at $0.06 per square foot is used to cover a stack three high and three wide the covering cost would be approximately $1.68 per bale (28 times $0.06). Considering the interest on the investment for money spent on plastic, the cost would increase to about $1.75 a bale or $3.50 per ton if the bales weigh 1000 pounds. Because plastic generally lasts only one year, the $3.50 per ton would be an annual cost. This cost does not include a charge for labor, fasteners, tie downs, or weighty materials to secure the plastic.


Because of its relatively low cost, plastic is a very affractive alternative as a storage covering. However, plastic has several shortcomings. First, it does not “breathe.” If high moisture hay (above 20 percent) is sealed under plastic, heavy losses in dry matter and forage quality can occur due to excessive heating and mold development. Second, nonreinforced plastic requires continual maintenance. High winds can cause large tears which must be repaired as quickly as possible. For this reason, consider using reinforced plastic. It withstands punctures and tears and with proper handling and storage between uses can last over three years. To help reduce tearing in any type of covering, weight the cover along the edges and ends to allow some movement. Do not tie a cover down tight!


Cover requirements for large round bale storage.


Figure 1. Cover requirements for large round bale storage.


Under-Roof Storage


Building Design

Dry matter losses in round bales stored up to nine months in an enclosed barn should be less than two percent (Table 2). If bales are stored in an open-sided barn (roof only) for over a year, losses can range up to 10 percent. Most commercial hay producers use enclosed barns with no more than one side open to minimize dry matter loss and to maintain good hay color, which is often used as a visual indicator of quality. For Oklahoma conditions, the opening should be to the east to prevent snow and rain from blowing into the building. The storage space should be clear to eliminate working around interior poles. New buildings should be located on a well-drained site near the feeding area.


There are particular sizes of buildings that work best for round bale storage. Stated building dimensions are usually only exterior measurements. Therefore, a 24-foot wide building will not provide adequate space for four 6-foot diameter bales placed side by side. Height of the storage system is another important consideration. If bales are stacked, interior height clearance should be at least two feet higher than the finished stack height (Figures 1 and 2). Table 5 shows approximate bale storage capacities for selected building sizes. Table 6 gives the approximate building space requirements based on bale size and weight.


Under-roof storage with bales stacked vertically and then one in pyramid pattern..


Figure 2. Under-roof storage with bales stacked vertically.


TOP: Bales stacked on side.
NOTE: Sidewalls must be built to withstand horizontal pressures from each row of bales.
BOTTOM: Bales stacked on end.


Under-roof storage with bales stacked in pyramid pattern.


Figure 3. Under-roof storage with bales stacked in pyramid pattern.


Building Costs

Storage costs for hay stored in a building depends on the initial cost of the structure and amount of area required to store each ton of hay. Initial cost of a building depends on building style, materials, and labor costs. For turn-key buildings, labor costs often represent over 35 percent of the building price. If a producer provides a large share of the labor, the initial cost can be greatly reduced. Initial cost of construction can range from less than $1.50 per square foot for a roof-only structure to over $6.00 per square foot for a turn-key enclosed building.


The following factors determine the annual cost of a building:

  • Depreciation (D) is the cost associated with normal life or wear out of the building. Most farm buildings will have a useful life of 15 to 20 years. Using a straight-line method, the annual depreciation is found by dividing the initial cost by the anticipated years of useful life.
  • Interest on investment (I) reflects the cost of borrowing money or, if money is not borrowed, the money that could have been earned in interest if invested. For convenience, assume the interest on investment is equal to 
    2/3 of the current annual interest rate. Investment interest over the past decade has ranged from about 7 to 11 percent while interest on borrowed money has ranged from 12 to 18 percent. Therefore, interest on investment has ranged from about 5 to 12 percent:
  • Repairs (R), taxes (T), and insurance (I) for a hay storage are normally estimated at about 0.7 percent, 1.0 percent, and 0.3 percent of initial cost, respectively.


Annual building cost is determined by multiplying the initial investment by the sum of all annual DIRTI percentages. For example, a proposed hay storage structure costs $3 per square foot to construct and has an expected life of 15 years. Depreciation is equal to 6.7 percent of the initial cost (100 percent divided by 15). Money is borrowed to construct the building at an interest rate of 15 percent. Interest on investment is equal to 10 percent of initial cost (15 percent times 2/3 ). Therefore, the annual building cost (DIRTI) is estimated at 18.7 percent (6.7 + 10 + 0.7 + 1.0 + 0.3) of the initial investment or $0.56 per square foot ($3 times 0. 187).


The annual building cost can be converted into a cost per ton of hay by multiplying it by the building space requirements. If bales 5-foot diameter by 5 feet long weighing 1,000 pounds were vertically stacked, three high, in a 36 foot by 64 foot building, about 231 bales could be stored (Table 5) in a building providing 21 square feet per ton (Table 6). If the annual building cost was $0.56 per square foot, annual storage cost would be $11.76 per ton (21 times $0.56).


Table 5A. Large round bale storage capacities.

      Vertical Stack (Figure 1)a    
  Building size 5ft Dia x 5ft   6ft Dia x 6ft  
    2- high 3-high  2-high 3-high
    Number of bales      
  26' x 64' 110 165 88 132
  32' x 64' 132 198 110 165
  36' x 64' 154 231    
  38' x 64'     132 198
  42' x 64' 176 264   165
  44' x 64'     154 231
  46' x 64'  198 297    
  50' x 64'     176 264

 a Assumes about 4 feet of unused space at one end.


Table 5B. Large round bale storage capacities.

      Pyramid Pattern (Figure 2)a    
Building size 5ft Dia x 5ft   6ft Dia x 6ft  
  2-high 3-high 2-high 3-high
     Number of bales    
26' x 64' 99 132 77 99
32' x 64' 121 165 99 132
36' x 64' 143 198    
38' x 64'     121 165
42' x 64' 165 231    
44' x 64'     143 198
46' x 64' 187 264    
50' x 64'     165 231

a Assumes about 4 feet of unused space at one end.


Table 6. Building space requirement for large round bales.

     Vertical Stack (Figure 1)          Pyramid Pattern (Figure 2)    
Bale weight, lb 5ft Dia x 5ft   6ft Dia x 6ft     5ft Dia x 5ft   6ft Dia x 6ft  
  2-high 3-high 2-high 3-high   2-high 3-high 2-high 3-high
    Square feet per ton         Square feet per ton    
600 51 34       55 39    
700 44 29       47 33    
800 38 26 46 32   41 29 49 36
900 34 23 41 28   36 26 44 32
1000 31 21 37 26   33 23 40 29
1100 28 19 34 23   30 21 36 26
1200 26 17 31 21   27 20 33 24
1300     29 20       30 22
1400     27 18       28 20
1500     25 17       26 19
1600     23 16       25 18


Total Storage Cost

The total storage cost is the sum of the storage system (such as covers and buildings) and the cost of the projected losses while bales are in storage. Using the results of the previous building example, the total storage cost per ton of $80 alfalfa hay with an estimated in-barn storage loss of two percent ($1.60 per ton) for less than nine months storage period would be $13.36 per ton ($11 .76 per ton building cost plus $1.60 per ton loss in hay value).


If the bales were stored under a plastic cover, storage cost with an estimated eight percent ($6.40 per ton) dry matter loss would be about $10 per ton ($3.60 per ton plastic cost plus $6.40 per ton loss in hay value). Note: This does not include the costs for labor or materials to secure the cover.


If the same bales were stored outside uncovered, loss of hay value could be as much as 10 percent or $8 per ton. This assumes the bales are well-shaped with a tight outer layer, but in contact with the ground. If elevated, the dry matter loss can be less than four percent or $4 per ton.


With estimated storage costs of $13.36 per ton for in barn storage, $10.00 per ton for covers, and $4.00 to $8.00 per ton for no protection, it would appear that providing protection is not cost effective. However, these estimates do not include the losses in quality or consider the end user. Commercial hay producers could have difficulties marketing hay to dairies if bales are stored outside and unprotected, especially during periods of surplus hay supplies. If the hay producer is going to feed this hay to his/her own beef herd, then the losses associated with bales stored outside and unprotected may not be a major concern.



All forages packaged in large round bales benefit from protection while in storage. However, there are several factors that must be considered in justifying the cost of providing this protection. These factors include hay value, projected in-storage losses, local environmental conditions, and where the hay will be used. If round bales are stored outside and unprotected, losses can be greatly reduced by storing only those bales that are well-shaped with dense outer layers; keeping bales off the ground to eliminate wicking; and using these bales before spring warm-up to avoid excessive weathering.


Raymond L. Huhnke
Extension Agricultural Engineer

Was this information helpful?
Fact Sheet
Minerals for Horses: Calcium and Phosphorus

By Kris Hiney. Learn about the most commonly talked about minerals that are often deficient in equine nutrition, Ca and P.

HayHorsesLivestockLivestock Health, Disease & NutritionLivestock NutritionPasturesPastures & Forage
Fact Sheet
Oklahoma Cropland Rental Rates: 2020-21

A 2020-2021 survey reporting the rental agreements, rates and influencing factors of leasing farmland in Oklahoma.

AlfalfaCottonCrop EconomicsCropsGrains & OilseedsHayPastures & ForageSoybeans
Fact Sheet
Agronomic Calendar for Oklahoma Alfalfa Growers

Management strategies including variety selection, soil nutrients, weed management, hay cutting, curing, baling and marketing for alfalfa crops.

AlfalfaHayInsects, Pests, and DiseasesLivestockPastures & ForageWeed ControlWeeds & Invasive Plants
Fact Sheet
Back To Top