Pesticide Safety Education
The Oklahoma Department of Agriculture, Food and Forestry funds a program to collect and properly dispose of unwanted pesticides that farmers, homeowners, commercial applicators, or dealers may have.
Frequently Requested Information
Links to ODAFF’s website
- Oklahoma Agriculture Food and Forestry
- Check your CEU’s
- CEU Meetings
- CEU Request Form
- ODAFF Pesticide Sensitive Crop Information
- ODAFF Pesticide Sensitive Crops Location Viewer
- ODAFF Pesticide Sensitive Crops Locations Registry Form
Crop Protection Reference Label and MSDS Information
Modes of Action
Pesticide Drift & Prevention
Select a nozzle that produces coarser (larger) droplets.
Use nozzles that provide as coarse (large) droplet as practical to provide necessary coverage. Some labels may require specific droplet size for there use. Nozzle selection guides should give you a listing of droplet size provided by each nozzle. New air induction nozzles help produce larger droplets.
Use lower pressure on the sprayer and larger nozzles when possible.
Higher pressures generate many more small droplets (less than 100 microns). Under most conditions, do not exceed 40 to 45 psi. Use larger nozzles to increase flow rate instead of higher pressure. Larger nozzles allow more volume (GPA) at lower pressures.
Lower boom height.
Wind speed increases with height. If boom height is a few inches lower, off-target drift is reduced. Keep boom as close as possible to the crop being sprayed.
Spray when wind speeds are low to avoid off target movement.
More spray will move off-target as wind increases. Some labels may specify specific wind speeds to make an application. Check wind speed with a hand held anemometer or the mesonet system before spraying.
Spray when wind is moving away from sensitive crops.
Leave a buffer zone 50 to 100 feet in width (or larger if needed) if sensitive plants are downwind. Spray the buffer zone when the wind changes direction away from the sensitive crop.
Do not spray when the air is very calm.
Calm air, or an inversion, reduces air mixing, which means spray can move slowly downwind. Inversions generally occur in early morning or near bodies of water.
Avoid high volatile formulations.
Avoid ester formulations of certain types of herbicides which can easily volatize in warm temperatures (above 80 F). Amine formulations are very unlikely to volatize but can still cause particle drift.
Check ODAFF’s pesticide sensitive viewer for pesticide sensitive crops.
Use this Oklahoma Department of Agriculture, Food and Forestry tool to be aware of pesticide sensitive crops near where you will be spraying. Take appropriate measures to protect these crops this may even mean delaying the application. Be aware of surrounding areas when making applications. The listing can be found on the ODAFF Kelly Solutions site.
- Follow label recommendations to avoid drift with pesticides.Labels may have specific requirements or directions for use to avoid drift of those products.
- Select the time when drift is less likely to occur.Certain time periods may be best for applications. On many occasions applications may have to be delayed days or weeks for favorable conditions.
- Oklahoma (ODAFF) Pesticide Regulations and Forms
- Pesticide Fact Sheets
- Plant Disease & Insect Diagnostic Lab (PDIDL)
- Plastic Pesticide Container Recycling
- Unwanted Pesticide Disposal Program
- Worker Protection Standard
- Certification to Apply RUPs in Indian Country
- Online Paraquat Training
- Associations and Helpful Links
If you would like to be added to our mailing list please send a email to Charles Luper. In the table below you can find the monthly pesticide reports.
- January 2018 Pesticide Report
- February 2018 Pesticide Report
- March 2018 Pesticide Report
- April 2018 Pesticide Report
- May 2018 Pesticide Report
- June 2018 Pesticide Report
- July 2018 Pesticide Report
- August 2018 Pesticide Report
- September 2018 Pesticide Report
- October 2018 Pesticide Report
- November 2018 Pesticide Report
- December 2018 Pesticide Report